Setting up A Bathtub
Setting up A Bathtub
Blog Article
They are making a few good points regarding How to Install a Bathtub Yourself overall in the article in the next paragraphs.
Mounting a bathtub isn't specifically rocket science, yet it does require solid plumbing, woodworking, and in some cases, tiling abilities. Changing an old tub with a brand-new one is also a reasonably hard project. If the old bathtub is readily easily accessible, the task can move rapidly; if you need to open a wall surface to get rid of the old tub as well as position the new bath tub, the task is much harder. In either instance, the project is within a house handyman's abilities, although you will need a helper to vacate the old tub as well as embeded in the new one. Ensure you have actually certified yourself for the task and also are comfortable attempting it. As opposed to hiring a professional to take control of a halfway-completed task, it is better to think about using one prior to you begin. Possibilities are you may require a specialist plumber to make tube connections.
This short article will certainly aid you install a new tub in your shower room if you have actually currently acquired a brand-new tub and don't need to alter the setup of your previous water supply pipes.
Your tools as well as product list need to comprise the following:
Preparing for the Installation
First of all, the supporting frame supplied with the bath ought to be fitted (if needed) according to the producer's directions. Next, fit the taps or mixer to the tub. When fitting the tap block, it is very important to ensure that if the tap includes a plastic washer, it is fitted between the bath and the taps. On a plastic bath, it is also sensible to fit a supporting plate under the taps device to stop pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets utilizing 2 nuts as well as olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you utilize all of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath need to currently be ready to be fitted in its final placement.
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, then the first thing you need to do is detach the supply of water. After doing so, turn on the faucets to drain any water continuing to be in the system. The procedure of removing the existing faucets can be rather troublesome due to the limited gain access to that is frequently the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will originate from the pipelines. Once the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning throughout this process. When the taps have actually been removed, the holes in the bath/basin will certainly have to be cleansed of any type of old securing substance.
Prior to proceeding to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is needed for the new faucets to fit.
Installing the Tub
Using the two wood boards under its feet, put the bath tub in the required placement. The wooden boards are valuable in equally spreading the weight of the bath tub over the area of the boards rather than concentrating all the weight onto four little points.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level and also changing the feet on the bath tub until the spirit level checks out degree.
To install faucets, fit all-time low of the furthest versatile faucet connector to the proper supply pipeline by making a compression join; after that do the same for the various other faucet.
Switch on the water system and also check all joints as well as brand-new pipework for leakages and tighten them if required. Load the tub as well as also check the overflow outlet as well as the regular outlet for leaks.
Lastly, deal with the bathroom paneling as described in the producer's instruction manual. Tiling and also sealing around the tub must wait till the bath tub has been utilized a minimum of when as this will certainly resolve it right into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will certainly require a plastic adapter to stop damages to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end supplies a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the faucet in the mounting hole in the bath/basin making sure that the washing machines remain in area in between the faucet as well as the sink. Safeguard the faucet in position with the maker given backnut. As soon as the faucet is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap connectors. The former kind needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bathroom fulfills the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split a stiff seal, causing the water to penetrate the wall surface in between the bathroom and the tiling, leading to issues with dampness and feasible leakages to the ceiling below.
You can choose from a selection of coloured sealers to blend in your fixtures and also installations. They are offered in tubes as well as cartridges, and can securing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to load, you can load it with twists of soaked paper or soft rope. Keep in mind to always load the tub with water prior to sealing, to allow for the movement experienced when the bathtub remains in use. The sealant can crack rather very early if you do not take into consideration this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally quickly offered on the market. It is suggested to fit the tiles making use of waterproof or water resistant adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I'm very inquisitive about How to Install a Bathtub and I really hope you liked the post. Sharing is caring. Helping others is fun. Thanks a lot for your time. Visit us again soon.
This Site
Report this page